{"id":6735,"date":"2026-11-17T01:36:55","date_gmt":"2026-11-17T09:36:55","guid":{"rendered":"https:\/\/www.tfngj.com\/?p=6735"},"modified":"2026-11-17T01:36:56","modified_gmt":"2026-11-17T09:36:56","slug":"underground-pipe-locator-route-depth","status":"publish","type":"post","link":"https:\/\/www.tfngj.com\/pt\/underground-pipe-locator-route-depth\/","title":{"rendered":"How an Underground Pipe Locator Finds Route and Depth"},"content":{"rendered":"<p class=\"wp-block-paragraph\"><strong>Short answer:<\/strong>&nbsp;An underground pipe locator finds a buried metal pipe or cable by putting an alternating-current signal onto the line and then measuring the magnetic field that the current produces. The transmitter applies the signal by&nbsp;<strong>direct connection, clamp coupling, or induction<\/strong>. The current then sets up a magnetic field around the line, and the field gets weaker the farther you move from it. Coils in the receiver pick up that field. The point of&nbsp;<strong>strongest signal (peak)<\/strong>&nbsp;ou&nbsp;<strong>weakest signal (null)<\/strong>&nbsp;marks the spot directly above the line. Depth comes either from a direct on-screen reading or from the 80% method. The TFN T6000 follows exactly this workflow, and the four steps below walk through it as you would do it on site.<\/p>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color has-3-x-large-font-size wp-elements-1\" id=\"why-accurate-pipe-locating-matters\"><strong>Why Accurate Pipe Locating Matters<\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Striking a buried service is one of the most common and most expensive mistakes in excavation work. In the U.S., the Common Ground Alliance&#8217;s 2024 DIRT Report found that\u00a0failure to notify 811 caused 24.54% of reported damages, and that\u00a0excavators failing to maintain clearance after verifying marks caused 16.07%\u00a0(<a href=\"https:\/\/compactequip.com\/business\/cga-releases-2024-dirt-report-findings-highlights-need-for-industry-improvements\/\" target=\"_blank\" rel=\"noopener\">CGA 2024 DIRT Report findings<\/a>). The UK Health and Safety Executive&#8217;s guidance HSG47 makes the same point. It treats locating devices as a core part of safe digging, together with plans and safe excavation practice (<a href=\"https:\/\/www.hse.gov.uk\/pubns\/books\/hsg47.htm\" target=\"_blank\" rel=\"noopener\">HSE \u2014 Avoiding danger from underground services, HSG47<\/a>).<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A locator is only as good as the person using it. Knowing&nbsp;<em>why<\/em>&nbsp;the signal behaves the way it does helps you spot a bad reading before it turns into a damaged gas main.<\/p>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color has-3-x-large-font-size wp-elements-2\" id=\"how-does-electromagnetic-induction-locate-a-buried-pipe\"><strong>How Does Electromagnetic Induction Locate a Buried Pipe?<\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">All of electromagnetic pipe locating rests on two physical laws. A current creates a magnetic field, and a changing magnetic field induces a voltage.<\/p>\n\n\n\n<figure data-wp-context=\"{&quot;imageId&quot;:&quot;6afca5d8868df&quot;}\" data-wp-interactive=\"core\/image\" data-wp-key=\"6afca5d8868df\" class=\"wp-block-image size-large wp-lightbox-container\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"683\" data-wp-class--hide=\"state.isContentHidden\" data-wp-class--show=\"state.isContentVisible\" data-wp-init=\"callbacks.setButtonStyles\" data-wp-on--click=\"actions.showLightbox\" data-wp-on--load=\"callbacks.setButtonStyles\" data-wp-on--pointerdown=\"actions.preloadImage\" data-wp-on--pointerenter=\"actions.preloadImageWithDelay\" data-wp-on--pointerleave=\"actions.cancelPreload\" data-wp-on-window--resize=\"callbacks.setButtonStyles\" src=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle-1024x683.webp\" alt=\"How an underground pipe locator detects the magnetic field around a buried metal pipe\" class=\"wp-image-6740\" srcset=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle-1024x683.webp 1024w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle-300x200.webp 300w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle-768x512.webp 768w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle-18x12.webp 18w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp 1248w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><button\n\t\t\tclass=\"lightbox-trigger\"\n\t\t\ttype=\"button\"\n\t\t\taria-haspopup=\"dialog\"\n\t\t\tdata-wp-bind--aria-label=\"state.thisImage.triggerButtonAriaLabel\"\n\t\t\tdata-wp-init=\"callbacks.initTriggerButton\"\n\t\t\tdata-wp-on--click=\"actions.showLightbox\"\n\t\t\tdata-wp-style--right=\"state.thisImage.buttonRight\"\n\t\t\tdata-wp-style--top=\"state.thisImage.buttonTop\"\n\t\t>\n\t\t\t<svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"12\" height=\"12\" fill=\"none\" viewbox=\"0 0 12 12\">\n\t\t\t\t<path fill=\"#fff\" d=\"M2 0a2 2 0 0 0-2 2v2h1.5V2a.5.5 0 0 1 .5-.5h2V0H2Zm2 10.5H2a.5.5 0 0 1-.5-.5V8H0v2a2 2 0 0 0 2 2h2v-1.5ZM8 12v-1.5h2a.5.5 0 0 0 .5-.5V8H12v2a2 2 0 0 1-2 2H8Zm2-12a2 2 0 0 1 2 2v2h-1.5V2a.5.5 0 0 0-.5-.5H8V0h2Z\" \/>\n\t\t\t<\/svg>\n\t\t<\/button><\/figure>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"1-the-transmitter-puts-an-alternating-current-on-the-line\"><strong>1. The transmitter puts an alternating current on the line<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The transmitter generates an AC signal at a specific frequency and drives it onto the target conductor. It can do this in three ways:<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-left\" data-align=\"left\">Method<\/th><th class=\"has-text-align-left\" data-align=\"left\">How the signal reaches the line<\/th><th class=\"has-text-align-left\" data-align=\"left\">Typical use<\/th><\/tr><\/thead><tbody><tr><td><strong>Direct connection<\/strong><\/td><td>Clip leads attach to the de-energized conductor. Current flows out along the line and returns through the earth.<\/td><td>Strongest, cleanest signal. The first choice whenever you can safely access the line.<\/td><\/tr><tr><td><strong>Clamp coupling<\/strong><\/td><td>A clamp around a live cable induces the signal into it without breaking the circuit.<\/td><td>Energized cables that cannot be shut down.<\/td><\/tr><tr><td><strong>Induction<\/strong><\/td><td>A coil inside the transmitter radiates a primary field that induces current in buried conductors below it. No contact is needed.<\/td><td>Blind searches, lines with no access point, and shallow lines.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure data-wp-context=\"{&quot;galleryId&quot;:&quot;6afca5d886d56&quot;}\" data-wp-interactive=\"core\/gallery\" class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-1 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure data-wp-context=\"{&quot;imageId&quot;:&quot;6afca5d887099&quot;}\" data-wp-interactive=\"core\/image\" data-wp-key=\"6afca5d887099\" class=\"wp-block-image size-large wp-lightbox-container\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"683\" data-wp-class--hide=\"state.isContentHidden\" data-wp-class--show=\"state.isContentVisible\" data-wp-init=\"callbacks.setButtonStyles\" data-wp-on--click=\"actions.showLightbox\" data-wp-on--load=\"callbacks.setButtonStyles\" data-wp-on--pointerdown=\"actions.preloadImage\" data-wp-on--pointerenter=\"actions.preloadImageWithDelay\" data-wp-on--pointerleave=\"actions.cancelPreload\" data-wp-on-window--resize=\"callbacks.setButtonStyles\" data-id=\"6741\" src=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method-1024x683.webp\" alt=\"Direct connection method of a pipe locator with ground stake and signal loop\" class=\"wp-image-6741\" srcset=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method-1024x683.webp 1024w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method-300x200.webp 300w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method-768x512.webp 768w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method-18x12.webp 18w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-direct-connection-method.webp 1248w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><button\n\t\t\tclass=\"lightbox-trigger\"\n\t\t\ttype=\"button\"\n\t\t\taria-haspopup=\"dialog\"\n\t\t\tdata-wp-bind--aria-label=\"state.thisImage.triggerButtonAriaLabel\"\n\t\t\tdata-wp-init=\"callbacks.initTriggerButton\"\n\t\t\tdata-wp-on--click=\"actions.showLightbox\"\n\t\t\tdata-wp-style--right=\"state.thisImage.buttonRight\"\n\t\t\tdata-wp-style--top=\"state.thisImage.buttonTop\"\n\t\t>\n\t\t\t<svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"12\" height=\"12\" fill=\"none\" viewbox=\"0 0 12 12\">\n\t\t\t\t<path fill=\"#fff\" d=\"M2 0a2 2 0 0 0-2 2v2h1.5V2a.5.5 0 0 1 .5-.5h2V0H2Zm2 10.5H2a.5.5 0 0 1-.5-.5V8H0v2a2 2 0 0 0 2 2h2v-1.5ZM8 12v-1.5h2a.5.5 0 0 0 .5-.5V8H12v2a2 2 0 0 1-2 2H8Zm2-12a2 2 0 0 1 2 2v2h-1.5V2a.5.5 0 0 0-.5-.5H8V0h2Z\" \/>\n\t\t\t<\/svg>\n\t\t<\/button><\/figure>\n\n\n\n<figure data-wp-context=\"{&quot;imageId&quot;:&quot;6afca5d88758f&quot;}\" data-wp-interactive=\"core\/image\" data-wp-key=\"6afca5d88758f\" class=\"wp-block-image size-large wp-lightbox-container\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"683\" data-wp-class--hide=\"state.isContentHidden\" data-wp-class--show=\"state.isContentVisible\" data-wp-init=\"callbacks.setButtonStyles\" data-wp-on--click=\"actions.showLightbox\" data-wp-on--load=\"callbacks.setButtonStyles\" data-wp-on--pointerdown=\"actions.preloadImage\" data-wp-on--pointerenter=\"actions.preloadImageWithDelay\" data-wp-on--pointerleave=\"actions.cancelPreload\" data-wp-on-window--resize=\"callbacks.setButtonStyles\" data-id=\"6739\" src=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram-1024x683.webp\" alt=\"Coupling method: signal clamp on a live cable for underground cable locating\" class=\"wp-image-6739\" srcset=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram-1024x683.webp 1024w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram-300x200.webp 300w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram-768x512.webp 768w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram-18x12.webp 18w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/Coupling-Clamp-Signal-Return-Diagram.webp 1536w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><button\n\t\t\tclass=\"lightbox-trigger\"\n\t\t\ttype=\"button\"\n\t\t\taria-haspopup=\"dialog\"\n\t\t\tdata-wp-bind--aria-label=\"state.thisImage.triggerButtonAriaLabel\"\n\t\t\tdata-wp-init=\"callbacks.initTriggerButton\"\n\t\t\tdata-wp-on--click=\"actions.showLightbox\"\n\t\t\tdata-wp-style--right=\"state.thisImage.buttonRight\"\n\t\t\tdata-wp-style--top=\"state.thisImage.buttonTop\"\n\t\t>\n\t\t\t<svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"12\" height=\"12\" fill=\"none\" viewbox=\"0 0 12 12\">\n\t\t\t\t<path fill=\"#fff\" d=\"M2 0a2 2 0 0 0-2 2v2h1.5V2a.5.5 0 0 1 .5-.5h2V0H2Zm2 10.5H2a.5.5 0 0 1-.5-.5V8H0v2a2 2 0 0 0 2 2h2v-1.5ZM8 12v-1.5h2a.5.5 0 0 0 .5-.5V8H12v2a2 2 0 0 1-2 2H8Zm2-12a2 2 0 0 1 2 2v2h-1.5V2a.5.5 0 0 0-.5-.5H8V0h2Z\" \/>\n\t\t\t<\/svg>\n\t\t<\/button><\/figure>\n\n\n\n<figure data-wp-context=\"{&quot;imageId&quot;:&quot;6afca5d887a7d&quot;}\" data-wp-interactive=\"core\/image\" data-wp-key=\"6afca5d887a7d\" class=\"wp-block-image size-large wp-lightbox-container\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"683\" data-wp-class--hide=\"state.isContentHidden\" data-wp-class--show=\"state.isContentVisible\" data-wp-init=\"callbacks.setButtonStyles\" data-wp-on--click=\"actions.showLightbox\" data-wp-on--load=\"callbacks.setButtonStyles\" data-wp-on--pointerdown=\"actions.preloadImage\" data-wp-on--pointerenter=\"actions.preloadImageWithDelay\" data-wp-on--pointerleave=\"actions.cancelPreload\" data-wp-on-window--resize=\"callbacks.setButtonStyles\" data-id=\"6742\" src=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method-1024x683.webp\" alt=\"Induction method: pipe locator transmitter inducing signal into a buried pipe\" class=\"wp-image-6742\" srcset=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method-1024x683.webp 1024w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method-300x200.webp 300w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method-768x512.webp 768w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method-18x12.webp 18w, https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-induction-method.webp 1248w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><button\n\t\t\tclass=\"lightbox-trigger\"\n\t\t\ttype=\"button\"\n\t\t\taria-haspopup=\"dialog\"\n\t\t\tdata-wp-bind--aria-label=\"state.thisImage.triggerButtonAriaLabel\"\n\t\t\tdata-wp-init=\"callbacks.initTriggerButton\"\n\t\t\tdata-wp-on--click=\"actions.showLightbox\"\n\t\t\tdata-wp-style--right=\"state.thisImage.buttonRight\"\n\t\t\tdata-wp-style--top=\"state.thisImage.buttonTop\"\n\t\t>\n\t\t\t<svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"12\" height=\"12\" fill=\"none\" viewbox=\"0 0 12 12\">\n\t\t\t\t<path fill=\"#fff\" d=\"M2 0a2 2 0 0 0-2 2v2h1.5V2a.5.5 0 0 1 .5-.5h2V0H2Zm2 10.5H2a.5.5 0 0 1-.5-.5V8H0v2a2 2 0 0 0 2 2h2v-1.5ZM8 12v-1.5h2a.5.5 0 0 0 .5-.5V8H12v2a2 2 0 0 1-2 2H8Zm2-12a2 2 0 0 1 2 2v2h-1.5V2a.5.5 0 0 0-.5-.5H8V0h2Z\" \/>\n\t\t\t<\/svg>\n\t\t<\/button><\/figure>\n<\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The signal needs a\u00a0complete loop. With direct connection, current leaves on the target line and returns through the soil to the transmitter&#8217;s ground stake. This is why grounding quality and loop impedance have a direct effect on how much current actually reaches the line.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"2-the-current-produces-a-magnetic-field-around-the-line\"><strong>2. The current produces a magnetic field around the line<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">By Amp\u00e8re&#8217;s law, current flowing in a long straight conductor produces\u00a0circular magnetic field lines centered on the conductor. The field strength falls off roughly in proportion to 1\/r, where r is the distance from the line. Directly above the pipe, the field lines run\u00a0horizontally. Off to either side, they tilt more and more toward the vertical. This simple geometry is what makes it possible to find both position and depth.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"3-the-receiver-turns-the-field-back-into-a-measurable-signal\"><strong>3. The receiver turns the field back into a measurable signal<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Because the current alternates, the magnetic field alternates too. By\u00a0Faraday&#8217;s law of induction, a changing magnetic flux through a coil induces a voltage in that coil (<a href=\"https:\/\/en.wikipedia.org\/wiki\/Faraday%27s_law_of_induction\" target=\"_blank\" rel=\"noopener\">Faraday&#8217;s law of induction<\/a>;\u00a0<a href=\"https:\/\/en.wikipedia.org\/wiki\/Electromagnetic_induction\" target=\"_blank\" rel=\"noopener\">Electromagnetic induction<\/a>). Each receiver coil responds only to the part of the field that runs along its axis. Coil orientation therefore determines what kind of response you see:<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-left\" data-align=\"left\">Response<\/th><th class=\"has-text-align-left\" data-align=\"left\">Coil orientation<\/th><th class=\"has-text-align-left\" data-align=\"left\">Reading directly over the line<\/th><th class=\"has-text-align-left\" data-align=\"left\">Strength<\/th><th class=\"has-text-align-left\" data-align=\"left\">Weakness<\/th><\/tr><\/thead><tbody><tr><td><strong>Peak<\/strong><\/td><td>Horizontal coil<\/td><td><strong>Maximum<\/strong>\u00a0signal, because the field is fully horizontal there<\/td><td>Stable and tolerant of field distortion<\/td><td>Broad response, so the exact center is less sharp<\/td><\/tr><tr><td><strong>Null (trough)<\/strong><\/td><td>Vertical coil<\/td><td><strong>Minimum<\/strong>&nbsp;signal, because the field has no vertical component there<\/td><td>Very sharp position indicator<\/td><td>Shifts easily when nearby conductors distort the field<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">On a clean, undistorted line, peak and null\u00a0point to the same spot. If they disagree, the field is being distorted by a tee, a bend, or a neighboring conductor. That is a cue to slow down and investigate before you mark.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"4-how-depth-can-be-read-from-the-field\"><strong>4. How depth can be read from the field<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Field strength drops with distance, so a receiver with\u00a0two horizontal coils stacked a known distance apart\u00a0can calculate depth. It compares the signal at the lower coil with the signal at the upper coil, and the ratio between the two depends on how far the line is below the receiver. This principle is what makes instant on-screen depth readings possible. Like any field-based estimate, it assumes the receiver is centered over the line and the field is undistorted.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"5-why-frequency-choice-matters\"><strong>5. Why frequency choice matters<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The frequency you pick changes how the signal behaves underground (<a href=\"https:\/\/www.simpleguideto.com.au\/a-simple-guide-to-the-different-underground-cable-and-pipe-locating-methods\/\" target=\"_blank\" rel=\"noopener\">A simple guide to cable and pipe locating methods<\/a>):<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-left\" data-align=\"left\">Frequ\u00eancia<\/th><th class=\"has-text-align-left\" data-align=\"left\">Behavior<\/th><th class=\"has-text-align-left\" data-align=\"left\">Best for<\/th><\/tr><\/thead><tbody><tr><td><strong>Lower<\/strong><\/td><td>Travels farther along the line and bleeds less onto neighboring utilities<\/td><td>Long runs and congested corridors<\/td><\/tr><tr><td><strong>Higher<\/strong><\/td><td>Couples more easily into conductors, including through insulating joints and by clamp or induction, but bleeds onto nearby lines more<\/td><td>Coupling and induction modes, short or poorly connected lines<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The T6000&#8217;s\u00a03-frequency synchronized output\u00a0lets you match the signal to pipes of different materials and depths without changing equipment.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"6-separating-the-target-from-lookalike-signals\"><strong>6. Separating the target from look-alike signals<\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">At higher frequencies, some signal &#8220;bleeds&#8221; onto adjacent conductors. These lines carry\u00a0return current flowing in the opposite direction\u00a0to the current on your target. A receiver that measures\u00a0current direction (signal phase)\u00a0can tell the outgoing current on the target line apart from these return currents. This is exactly what the T6000&#8217;s current-direction function does in Step 2 below. The T6000 also uses anti-interference algorithms to reduce the effect of adjacent pipelines and environmental noise.<\/p>\n\n\n\n<div style=\"height:26px\" aria-hidden=\"true\" class=\"wp-block-spacer\"><\/div>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color has-3-x-large-font-size wp-elements-3\" id=\"how-to-locate-a-metal-pipe-with-the-tfn-t6000-locator-a-4step-workflow\"><strong>How to Locate a Metal Pipe With <a href=\"https:\/\/www.tfngj.com\/pt\/underground-pipeline-locators\/t6000-underground-pipe-locator\/\">the TFN T6000 Locator<\/a>: A 4-Step Workflow<\/strong><\/h2>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"step-1-apply-the-signal-transmitter\"><strong>Step 1: Apply the Signal (Transmitter)<\/strong><\/h3>\n\n\n<ul class=\"wp-block-list\" style=\"\">\n<li>\n<strong><mark style=\"background-color:rgba(0, 0, 0, 0)\" class=\"has-inline-color has-primary-active-color\">Direct connection (preferred):<\/mark><\/strong>&nbsp;Connect the&nbsp;red clip&nbsp;to the phase conductor of the target cable. Connect the&nbsp;black clip&nbsp;to an independent ground stake. Disconnect the far-end ground wire so the signal forms a loop.&nbsp;Loop impedance must be below 3000 &Omega;.<\/li>\n\n\n\n<li>\n<strong><mark style=\"background-color:rgba(0, 0, 0, 0)\" class=\"has-inline-color has-primary-active-color\">Coupling method (live work):<\/mark><\/strong>&nbsp;Close the coupling clamp around the exposed cable. Select&nbsp;high frequency + high power&nbsp;to strengthen signal coupling.<\/li>\n\n\n\n<li>\n<strong><mark style=\"background-color:rgba(0, 0, 0, 0)\" class=\"has-inline-color has-primary-active-color\">Induction method (blind search or shallow lines):<\/mark><\/strong>&nbsp;Place the transmitter close to the ground. Its built-in antenna radiates a high-frequency signal into lines below it (<strong>depth &le; 10 m<\/strong>).<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.tfngj.com\/pt\/underground-pipeline-locators\/t6000-underground-pipe-locator\/\">The T6000 transmitter<\/a>\u00a0automatically detects impedance\u00a0and optimizes signal strength, so you spend less time adjusting output by hand.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"step-2-trace-the-route-receiver\"><strong>Step 2: Trace the Route (Receiver)<\/strong><\/h3>\n\n\n<ol class=\"wp-block-list\">\n<li>Turn on the receiver, select&nbsp;<em>Peak mode,<\/em> and set the gain to the&nbsp;<em>60 dB baseline<\/em>.<\/li>\n\n\n\n<li>Walk along the expected route and watch the signal strength bar and the digital value (00.0&ndash;99.9):<ul class=\"wp-block-list\" style=\"\">\n<li>\n<strong>Peak method:<\/strong>&nbsp;The point of maximum signal is directly above the line. The audio tone is at its fastest here.<\/li>\n\n\n\n<li>\n<strong>Null (trough) method:<\/strong>&nbsp;The point of minimum signal marks the center of the line. Use the on-screen arrows to confirm the route.<\/li>\n<\/ul>\n<\/li>\n\n\n\n<li>Use the&nbsp;current-direction function (SS frequency):<ul class=\"wp-block-list\" style=\"\">\n<li>Forward current shows a&nbsp;<strong>&#8220;+&#8221;<\/strong>&nbsp;sign (phase&nbsp;&minus;45&deg; to 45&deg;). Reverse current shows a&nbsp;<strong>&#8220;&minus;&#8221;<\/strong>&nbsp;sign (phase&nbsp;&minus;135&deg; to 225&deg;). This lets you rule out crosstalk signals from neighboring lines.<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"step-3-measure-burial-depth\"><strong>Step 3: Measure Burial Depth<\/strong><\/h3>\n\n\n<ul class=\"wp-block-list\" style=\"\">\n<li>\n<strong>Direct reading (real-time display):<\/strong>&nbsp;Hold the receiver directly over the line with the compass pointing straight ahead. The screen shows&nbsp;depth (meters)&nbsp;and&nbsp;current (mA)&nbsp;in the upper-left corner.<\/li>\n\n\n\n<li>\n<strong>80% method (complex environments):<\/strong><ol class=\"wp-block-list\" style=\"\">\n<li>Record the signal value directly above the line (for example,&nbsp;85.0).<\/li>\n\n\n\n<li>Calculate 80% of that value (85 &times; 0.8 = 68.0).<\/li>\n\n\n\n<li>Move sideways until the signal drops to&nbsp;68.0. The distance between the two points is the burial depth.<\/li>\n<\/ol>\n<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Tip: If the direct reading and the 80% result differ significantly, the field is likely distorted. Re-check the peak\/null agreement from Step 2 before you record a depth.<\/p>\n\n\n<h3 class=\"wp-block-heading has-x-large-font-size\" id=\"step-4-blindsearch-for-unknown-lines-induction-mode\"><strong>Step 4: Blind-Search for Unknown Lines (Induction Mode)<\/strong><\/h3>\n\n\n<ul class=\"wp-block-list\" style=\"\">\n<li>\n<strong>Area sweep (surface method):<\/strong>&nbsp;Keep the transmitter and receiver&nbsp;7 meters apart&nbsp;and move them slowly in parallel. Wherever the signal jumps, there is a line underneath. This works well for large-area surveys.<\/li>\n\n\n\n<li>\n<strong>Point search (radial method):<\/strong>&nbsp;Use the transmitter as the center point and walk the receiver around it on a&nbsp;7-meter-radius circle. Connect the signal peak points to get the line&#8217;s direction. This works well for precise positioning.<\/li>\n<\/ul>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color has-3-x-large-font-size wp-elements-4\" id=\"where-is-the-t6000-used\"><strong>Where Is the T6000 Used?<\/strong><\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-left\" data-align=\"left\">Application<\/th><th class=\"has-text-align-left\" data-align=\"left\">What the locator does<\/th><\/tr><\/thead><tbody><tr><td>Municipal construction<\/td><td>Keeps excavation clear of water, gas, and power lines<\/td><\/tr><tr><td>Fault finding<\/td><td>Pinpoints cable short-circuit points and damaged sections<\/td><\/tr><tr><td>Pipe network mapping<\/td><td>Produces underground utility maps at\u00a0\u00b15% of depth + 2.5 cm positioning accuracy<\/td><\/tr><tr><td>Emergency repair<\/td><td>Identifies buried lines fast to shorten repair time<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.tfngj.com\/pt\/underground-pipeline-locators\/t6000-underground-pipe-locator\/\">The T6000 locator<\/a>&#8216;s <strong>color compass navigation and audio intensity feedback<\/strong> also help reduce operator fatigue on long survey days.<\/p>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color has-3-x-large-font-size wp-elements-5\" id=\"safety-checklist-before-you-start\"><strong>Safety Checklist Before You Start<\/strong><\/h2>\n\n\n<ul class=\"wp-block-list\" style=\"\">\n<li>Operators should be&nbsp;professionally trained&nbsp;and must strictly follow grounding procedures.<\/li>\n\n\n\n<li>Do not use the equipment in flammable or explosive environments.<\/li>\n\n\n\n<li>Charge lithium batteries&nbsp;only with the dedicated charger, and dispose of used batteries according to local environmental regulations.<\/li>\n\n\n\n<li>A locator is one layer of protection, not a guarantee. Combine it with utility records, an 811 or local one-call notification, and careful hand digging near marks, as HSG47 recommends.<\/li>\n<\/ul>\n\n\n\n<div style=\"height:46px\" aria-hidden=\"true\" class=\"wp-block-spacer\"><\/div>\n\n\n<h2 class=\"wp-block-heading has-primary-color-color has-text-color has-link-color wp-elements-6\" id=\"faq\"><strong>PERGUNTAS FREQUENTES<\/strong><\/h2>\n\n\n\n<div class=\"schema-faq wp-block-yoast-faq-block\"><div class=\"schema-faq-section\" id=\"faq-question-1794905075762\"><strong class=\"schema-faq-question\">How does an underground pipe locator detect a metal pipe?<\/strong> <p class=\"schema-faq-answer\">It puts an AC signal on the pipe. The pipe then radiates a magnetic field, and coils in the receiver detect it. The receiver shows a peak (maximum) or null (minimum) directly above the pipe.<\/p> <\/div> <div class=\"schema-faq-section\" id=\"faq-question-1794907963840\"><strong class=\"schema-faq-question\">What is the difference between the peak and null methods?<\/strong> <p class=\"schema-faq-answer\">Peak uses a horizontal coil and reads strongest directly over the line. It is stable but broad. Null uses a vertical coil and reads weakest over the line. It is sharper but more sensitive to distortion. When both point to the same spot, the reading is reliable.<\/p> <\/div> <div class=\"schema-faq-section\" id=\"faq-question-1794907982359\"><strong class=\"schema-faq-question\">Which signal application method should I use?<\/strong> <p class=\"schema-faq-answer\">Use direct connection whenever you can safely access a de-energized line, because it gives the strongest signal. Use clamp coupling for live cables. Use induction for blind searches or when there is no access point. On the T6000, induction works to a depth of about 10 m.<\/p> <\/div> <div class=\"schema-faq-section\" id=\"faq-question-1794908008425\"><strong class=\"schema-faq-question\">What frequency should I choose?<\/strong> <p class=\"schema-faq-answer\">Lower frequencies travel farther and bleed less, so they suit long runs in congested areas. Higher frequencies couple better, so they suit clamp and induction modes. The T6000&#8217;s 3-frequency output lets you switch without changing equipment.<\/p> <\/div> <\/div>","protected":false},"excerpt":{"rendered":"<p>Short answer:&nbsp;An underground pipe locator finds a buried metal pipe or cable by putting an alternating-current signal onto the line and then measuring the magnetic field that the current produces. The transmitter applies the signal by&nbsp;direct connection, clamp coupling, or induction. The current then sets up a magnetic field around the line, and the field [&hellip;]<\/p>","protected":false},"author":1,"featured_media":6740,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[7],"tags":[],"class_list":["post-6735","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-tfn-blog"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v26.6 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How an Underground Pipe Locator Finds Route and Depth<\/title>\n<meta name=\"description\" content=\"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.tfngj.com\/pt\/underground-pipe-locator-route-depth\/\" \/>\n<meta property=\"og:locale\" content=\"pt_BR\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How an Underground Pipe Locator Finds Route and Depth\" \/>\n<meta property=\"og:description\" content=\"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.tfngj.com\/pt\/underground-pipe-locator-route-depth\/\" \/>\n<meta property=\"og:site_name\" content=\"Communication Test Expert\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T09:36:55+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-17T09:36:56+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp\" \/>\n\t<meta property=\"og:image:width\" content=\"1248\" \/>\n\t<meta property=\"og:image:height\" content=\"832\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/webp\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Escrito por\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. tempo de leitura\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 minutos\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/\"},\"author\":{\"name\":\"admin\",\"@id\":\"https:\/\/www.tfngj.com\/#\/schema\/person\/985f00c1219ceea14a6db990da997b5d\"},\"headline\":\"How an Underground Pipe Locator Finds Route and Depth\",\"datePublished\":\"2026-11-17T09:36:55+00:00\",\"dateModified\":\"2026-11-17T09:36:56+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/\"},\"wordCount\":1751,\"publisher\":{\"@id\":\"https:\/\/www.tfngj.com\/#organization\"},\"image\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp\",\"articleSection\":[\"Blogs\"],\"inLanguage\":\"pt-BR\"},{\"@type\":[\"WebPage\",\"FAQPage\"],\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/\",\"url\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/\",\"name\":\"How an Underground Pipe Locator Finds Route and Depth\",\"isPartOf\":{\"@id\":\"https:\/\/www.tfngj.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp\",\"datePublished\":\"2026-11-17T09:36:55+00:00\",\"dateModified\":\"2026-11-17T09:36:56+00:00\",\"description\":\"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#breadcrumb\"},\"mainEntity\":[{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762\"},{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840\"},{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359\"},{\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425\"}],\"inLanguage\":\"pt-BR\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"pt-BR\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage\",\"url\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp\",\"contentUrl\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp\",\"width\":1248,\"height\":832,\"caption\":\"How an underground pipe locator detects the magnetic field around a buried metal pipe\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.tfngj.com\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How an Underground Pipe Locator Finds Route and Depth\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.tfngj.com\/#website\",\"url\":\"https:\/\/www.tfngj.com\/\",\"name\":\"TFN-Communication Test Expert\",\"description\":\"Find Perfect Solutions in TFN\",\"publisher\":{\"@id\":\"https:\/\/www.tfngj.com\/#organization\"},\"alternateName\":\"TFN\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.tfngj.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"pt-BR\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/www.tfngj.com\/#organization\",\"name\":\"TFN Instruments\",\"url\":\"https:\/\/www.tfngj.com\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"pt-BR\",\"@id\":\"https:\/\/www.tfngj.com\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2025\/09\/\u9ed1logo.png\",\"contentUrl\":\"https:\/\/www.tfngj.com\/wp-content\/uploads\/2025\/09\/\u9ed1logo.png\",\"width\":939,\"height\":232,\"caption\":\"TFN Instruments\"},\"image\":{\"@id\":\"https:\/\/www.tfngj.com\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.youtube.com\/@FateTFN\/search\"]},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.tfngj.com\/#\/schema\/person\/985f00c1219ceea14a6db990da997b5d\",\"name\":\"admin\",\"sameAs\":[\"https:\/\/www.tfngj.com\"],\"url\":\"https:\/\/www.tfngj.com\/pt\/author\/admin\/\"},{\"@type\":\"Question\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762\",\"position\":1,\"url\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762\",\"name\":\"How does an underground pipe locator detect a metal pipe?\",\"answerCount\":1,\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"It puts an AC signal on the pipe. The pipe then radiates a magnetic field, and coils in the receiver detect it. The receiver shows a peak (maximum) or null (minimum) directly above the pipe.\",\"inLanguage\":\"pt-BR\"},\"inLanguage\":\"pt-BR\"},{\"@type\":\"Question\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840\",\"position\":2,\"url\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840\",\"name\":\"What is the difference between the peak and null methods?\",\"answerCount\":1,\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Peak uses a horizontal coil and reads strongest directly over the line. It is stable but broad. Null uses a vertical coil and reads weakest over the line. It is sharper but more sensitive to distortion. When both point to the same spot, the reading is reliable.\",\"inLanguage\":\"pt-BR\"},\"inLanguage\":\"pt-BR\"},{\"@type\":\"Question\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359\",\"position\":3,\"url\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359\",\"name\":\"Which signal application method should I use?\",\"answerCount\":1,\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Use direct connection whenever you can safely access a de-energized line, because it gives the strongest signal. Use clamp coupling for live cables. Use induction for blind searches or when there is no access point. On the T6000, induction works to a depth of about 10 m.\",\"inLanguage\":\"pt-BR\"},\"inLanguage\":\"pt-BR\"},{\"@type\":\"Question\",\"@id\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425\",\"position\":4,\"url\":\"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425\",\"name\":\"What frequency should I choose?\",\"answerCount\":1,\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Lower frequencies travel farther and bleed less, so they suit long runs in congested areas. Higher frequencies couple better, so they suit clamp and induction modes. The T6000's 3-frequency output lets you switch without changing equipment.\",\"inLanguage\":\"pt-BR\"},\"inLanguage\":\"pt-BR\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How an Underground Pipe Locator Finds Route and Depth","description":"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.tfngj.com\/pt\/underground-pipe-locator-route-depth\/","og_locale":"pt_BR","og_type":"article","og_title":"How an Underground Pipe Locator Finds Route and Depth","og_description":"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.","og_url":"https:\/\/www.tfngj.com\/pt\/underground-pipe-locator-route-depth\/","og_site_name":"Communication Test Expert","article_published_time":"2026-11-17T09:36:55+00:00","article_modified_time":"2026-11-17T09:36:56+00:00","og_image":[{"width":1248,"height":832,"url":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp","type":"image\/webp"}],"author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Escrito por":"admin","Est. tempo de leitura":"9 minutos"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#article","isPartOf":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/"},"author":{"name":"admin","@id":"https:\/\/www.tfngj.com\/#\/schema\/person\/985f00c1219ceea14a6db990da997b5d"},"headline":"How an Underground Pipe Locator Finds Route and Depth","datePublished":"2026-11-17T09:36:55+00:00","dateModified":"2026-11-17T09:36:56+00:00","mainEntityOfPage":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/"},"wordCount":1751,"publisher":{"@id":"https:\/\/www.tfngj.com\/#organization"},"image":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage"},"thumbnailUrl":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp","articleSection":["Blogs"],"inLanguage":"pt-BR"},{"@type":["WebPage","FAQPage"],"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/","url":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/","name":"How an Underground Pipe Locator Finds Route and Depth","isPartOf":{"@id":"https:\/\/www.tfngj.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage"},"image":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage"},"thumbnailUrl":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp","datePublished":"2026-11-17T09:36:55+00:00","dateModified":"2026-11-17T09:36:56+00:00","description":"Learn the electromagnetic principle and a 4-step location workflow to trace route and measure depth.","breadcrumb":{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#breadcrumb"},"mainEntity":[{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762"},{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840"},{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359"},{"@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425"}],"inLanguage":"pt-BR","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/"]}]},{"@type":"ImageObject","inLanguage":"pt-BR","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#primaryimage","url":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp","contentUrl":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2026\/11\/pipe-locator-electromagnetic-induction-principle.webp","width":1248,"height":832,"caption":"How an underground pipe locator detects the magnetic field around a buried metal pipe"},{"@type":"BreadcrumbList","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.tfngj.com\/"},{"@type":"ListItem","position":2,"name":"How an Underground Pipe Locator Finds Route and Depth"}]},{"@type":"WebSite","@id":"https:\/\/www.tfngj.com\/#website","url":"https:\/\/www.tfngj.com\/","name":"TFN - Especialista em testes de comunica\u00e7\u00e3o","description":"Encontre solu\u00e7\u00f5es perfeitas no TFN","publisher":{"@id":"https:\/\/www.tfngj.com\/#organization"},"alternateName":"TFN","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.tfngj.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"pt-BR"},{"@type":"Organization","@id":"https:\/\/www.tfngj.com\/#organization","name":"TFN Instruments","url":"https:\/\/www.tfngj.com\/","logo":{"@type":"ImageObject","inLanguage":"pt-BR","@id":"https:\/\/www.tfngj.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2025\/09\/\u9ed1logo.png","contentUrl":"https:\/\/www.tfngj.com\/wp-content\/uploads\/2025\/09\/\u9ed1logo.png","width":939,"height":232,"caption":"TFN Instruments"},"image":{"@id":"https:\/\/www.tfngj.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.youtube.com\/@FateTFN\/search"]},{"@type":"Person","@id":"https:\/\/www.tfngj.com\/#\/schema\/person\/985f00c1219ceea14a6db990da997b5d","name":"administrador","sameAs":["https:\/\/www.tfngj.com"],"url":"https:\/\/www.tfngj.com\/pt\/author\/admin\/"},{"@type":"Question","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762","position":1,"url":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794905075762","name":"How does an underground pipe locator detect a metal pipe?","answerCount":1,"acceptedAnswer":{"@type":"Answer","text":"It puts an AC signal on the pipe. The pipe then radiates a magnetic field, and coils in the receiver detect it. The receiver shows a peak (maximum) or null (minimum) directly above the pipe.","inLanguage":"pt-BR"},"inLanguage":"pt-BR"},{"@type":"Question","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840","position":2,"url":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907963840","name":"What is the difference between the peak and null methods?","answerCount":1,"acceptedAnswer":{"@type":"Answer","text":"Peak uses a horizontal coil and reads strongest directly over the line. It is stable but broad. Null uses a vertical coil and reads weakest over the line. It is sharper but more sensitive to distortion. When both point to the same spot, the reading is reliable.","inLanguage":"pt-BR"},"inLanguage":"pt-BR"},{"@type":"Question","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359","position":3,"url":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794907982359","name":"Which signal application method should I use?","answerCount":1,"acceptedAnswer":{"@type":"Answer","text":"Use direct connection whenever you can safely access a de-energized line, because it gives the strongest signal. Use clamp coupling for live cables. Use induction for blind searches or when there is no access point. On the T6000, induction works to a depth of about 10 m.","inLanguage":"pt-BR"},"inLanguage":"pt-BR"},{"@type":"Question","@id":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425","position":4,"url":"https:\/\/www.tfngj.com\/underground-pipe-locator-route-depth\/#faq-question-1794908008425","name":"What frequency should I choose?","answerCount":1,"acceptedAnswer":{"@type":"Answer","text":"Lower frequencies travel farther and bleed less, so they suit long runs in congested areas. Higher frequencies couple better, so they suit clamp and induction modes. The T6000's 3-frequency output lets you switch without changing equipment.","inLanguage":"pt-BR"},"inLanguage":"pt-BR"}]}},"_links":{"self":[{"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/posts\/6735","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/comments?post=6735"}],"version-history":[{"count":8,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/posts\/6735\/revisions"}],"predecessor-version":[{"id":6747,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/posts\/6735\/revisions\/6747"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/media\/6740"}],"wp:attachment":[{"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/media?parent=6735"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/categories?post=6735"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.tfngj.com\/pt\/wp-json\/wp\/v2\/tags?post=6735"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}